The Rowland Company
The Rowland Company
4900 North 20th St.
Philadelphia, PA 19144
Toll Free: (800) 925-8824
Phone: (215) 455-4900
Fax: (215) 455-8888
Email: rowland@rowland2.com
Print Back
Model DBB brakes are spring applied, pressure released, disc style brakes. They develop equal torque in either direction of rotation. Their torque and thermal capacities allow them to be used in the most demanding applications.

Brake construction and operation is shown in the figure. Pressurizing the brake compresses the brake springs and withdraws the clamping plates from the brake discs. Standard brakes are furnished with either one or two discs, which are free to move axially.

Model DBB uses a conventional piston design to release the brake discs.

The rotating component of the DBB style brake is a very low inertia friction disc core with riveted on friction discs. The low inertia of the rotating components coupled with the high heat sink capacity of the stationary members allow these units to provide superior performance in high cyclic applications. In applications requiring higher speed operation or where precise balance of the rotating components is required, the DBBS style is offered, which utilizes a solid rotor and stationary friction material. Similar to the DBAS design, the DBBS should only be used for applications where brake engagement is non-cyclic.

Torque ratings listed are for brakes with a standard compliment of springs. The quantity of springs can be varied to customize the torque of the brake to suit a particular application. Consult the factory for brake torque of units with non-standard spring configurations.

Brake sizes are indicated by the number of brake discs and the disc diameter in inches. For instance, size 225DBB has two discs 25 inches in diameter.
Unit of Measure

Features

N/A Low inertia friction disc assembly.
Reduces the overall inertia that must be stopped.

Optional split friction discs.
Allows removal of friction discs without disturbing other components of drive system in mid-shaft brake arrangement.

Long wearing, self lubricating PolyPak seals.
Eliminates premature twisting failure and requires no external lubrication.

Where Used

N/A

  • Bottling equipment
  • Power Shovels
  • Conveyors
  • Shears
  • Power Presses

Specifications

Model

 N/A 338DBBS

Dimension D

 N/A 22.60 in574 mm

Dimension D1

 N/A 13.00 in330 mm

Dimension D31

 N/A 2.45 in62 mm

Dimension D44

 N/A 0.25 in6 mm

Dimension D45

 N/A 1.00 in25 mm

Dimension H16

 N/A 16.50 in419 mm
Dimension J1 N/A 44.498 in1135.7 mm

Dimension J1

 N/A 36.375 in923.9 mm

Dimension J2

 N/A 45.00 in1143 mm

Dimension O2

 N/A 3/4-14 NPT

Minimum Bore

 N/A 9.63 in245 mm

Maximum Bore

 N/A 10.06 in256 mm

Dynamic Torque Rating

 N/A 1730000 lb·in195.325 Nm

Worn Torque Multiplier

 N/A 0.80

Disc & Gear (Inertia)

 N/A 1709 lb·ft²7210 kg·m²

Disc & Gear (Weight)

 N/A 1680 lb736 kg

Housing (Weight)

 N/A 4085 lb1.856 kg
Minimum Releasing Pressure2 N/A 90 psi6.2 bar

Maximum Speed

 N/A 950 rpm

Manufacturer

 N/A Eaton-Airflex

Actuation

 N/A Spring Applied, Air Release

Note

N/A Tolerance +0.000/-0.005 in (+0.00/-0.08 mm)
Brake in disengaged position.
Basic part number only. Does not include gear. Gear must be ordered separately with bore and keyway requirements.

  • 1 Tolerance +0.000/-0.005 in (+0.00/-0.08 mm)
  • 2 Maximum allowable cylinder pressure is 120 psi (8.3 bar).